By Instruction for Bathtub Installation
By Instruction for Bathtub Installation
Blog Article
The article which follows about How to Install a Bathtub Yourself is amazingly enlightening. You should see for yourself.
Mounting a bathtub isn't precisely rocket science, but it does require strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is readily available, the job can relocate rapidly; if you have to open up a wall to get rid of the old bathtub as well as position the brand-new tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub and set in the new one. See to it you have actually qualified yourself for the task and also are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is better to think about utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly help you install a new bathtub in your shower room if you have actually currently acquired a brand-new bathtub and also do not need to change the arrangement of your previous water system pipelines.
Your tools and also product checklist must consist of the following:
Planning for the Setup
First of all, the sustaining framework provided with the bath must be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final setting.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have actually been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Prior to moving on to fit the new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, position the bathtub in the needed placement. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system as well as check all joints as well as brand-new pipework for leaks and tighten them if essential. Fill the bath tub and additionally examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the bath tub should wait until the bathtub has been utilized at the very least once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap and also the sink. Protect the tap in position with the manufacturer provided backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous type needs to be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in problems with dampness and also feasible leakages to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our piece about How to Install a Bathtub Yourself. Thanks a ton for taking the time to browse our piece of content. Enjoyed reading our post? Please share it. Let others check it out. Thank-you for taking the time to read it.
End your worries, dial! Report this page